読み取り専用

フォーラムは現在、読み取り専用のアーカイブとなっています。.

バグ報告やプラットフォームに関する質問はこちら → [email protected]

私たちのコミュニティはDiscordとYouTubeで活動しています。ぜひ参加してください!

ご参加ください Discord YouTube

価格行動の条件に関する助言

8件の返信

simon972

Subscriber, bbp_participant, community, 10 replies.

プロフィールを表示

6年前 #256395

こんにちは

I am new to using AlgoWizard.  Can you please help me with how I create the following conditions in the Full Wizard, relating to my “Bar(1) is either:…” candlestick patterns:

短い rule:

If H(1) > indicator value
そして
Bar(1) is either:
a) a bar with a body (difference between Close & Open) that is < 0.8 pips; OR
b) a Down-bar, with prior bar(2) being an Up-bar, AND with C(1) < C(2) to a minimum degree of 60% of distance between C(2) to O(2), ie. bar(1) body must engulf at least 60% of body of bar(2); OR
c) a Down-bar, with prior bar(2) being an Down-bar, AND with C(1) < C(2), ie. bar(1) must C < body of bar(2)
Then Entry at open (0)

ELSE
If H(2) > indicator value
そして
Bar(1) is either:
a) a bar with a body (difference between Close & Open) that is < 0.8 pips; OR
b) a Down-bar, with prior bar(2) being an Up-bar, AND with C(1) < C(2) to a minimum degree of 60% of distance between C(2) to O(2), ie. bar(1) body must engulf at least 60% of body of bar(2); OR
c) a Down-bar, with prior bar(2) being an Down-bar, AND with C(1) < C(2), ie. bar(1) must C < body of bar(2)
Then Entry at open (0)

Very grateful for any help

0

simon972

Subscriber, bbp_participant, community, 10 replies.

プロフィールを表示

6年前 #256396

Just to clarify, the second “Bar(1) is either:…” section (after the ELSE If H(2) > indicator value) is exactly the same as the first. The only difference is the “If H(2) > indicator value” bit.

0

Tomas Matejka

管理者、sq-ultimate、2件の返信.

プロフィールを表示

6年前 #256620

こんにちは,

this seems not difficult but let me ask. Does the H stand for ‘High’? What is the indicator ‘indicator’ used?

0

simon972

Subscriber, bbp_participant, community, 10 replies.

プロフィールを表示

6年前 #256624

Thanks for replying.

Yes, H = High, C = Close, O = Open.  The indicator used is Bollinger Bands upper band; plus High[1] must be a new high of the current day so far (so I assume the way of expressing this is: High[1] > HighD[1])

🙂

0

Tomas Matejka

管理者、sq-ultimate、2件の返信.

プロフィールを表示

6年前 #256729

こんにちは,

find the example attached. Hope that helps

添付ファイル:
に違いない ログインしました 添付ファイルを表示するには.

0

simon972

Subscriber, bbp_participant, community, 10 replies.

プロフィールを表示

6年前 #256754

ありがとう、トーマス

I am a little confused by the bit:

(0.6 * Abs((Close(Main chart)[2] – Open(Main chart)[2]))) > Abs((Close(Main chart)[1] – Open(Main chart)[1]))

Isn’t this saying: 60% of bar(2)’s body must be greater than the entire body of bar(1)?

I think I probably didn’t explain this well, when I said:

b) a Down-bar, with prior bar(2) being an Up-bar,

AND with C(1) < C(2) to a minimum degree of 60% of distance between C(2) to O(2), ie. bar(1) body must engulf at least 60% of body of bar(2);

I meant the following:

b) a Down-bar, with prior bar(2) being an Up-bar,

AND Bar(1) must close at a price that is at least 60% below Bar(2)’s close, measured from Bar(2)’s close to its open, ie. basically where bar(1) closes must cover at least 60% of the previous bar’s body.

Please see attached image.

Secondly, could you please tell me how to add a Vertical line signal?  (I can only see the option to add a “Draw Down Arrow” action).

Your help is greatly appreciated!

添付ファイル:
に違いない ログインしました 添付ファイルを表示するには.

0

simon972

Subscriber, bbp_participant, community, 10 replies.

プロフィールを表示

6年前 #256894

Hello Tomas, are you able to help with this please?

0

Tomas Matejka

管理者、sq-ultimate、2件の返信.

プロフィールを表示

6年前 #256944

You are right, the comparison must be the opposite < instead of > used so the correct formula is

(0.6 * Abs((Close(Main chart)[2] – Open(Main chart)[2]))) < Abs((Close(Main chart)[1] – Open(Main chart)[1]))

meaning the current bar body (C – O) is larger than 60% of the previous bar body (C – O)

To add a vertical line on each trade entry add a new action – add a Custom action and set this as a command: “ObjectCreate(0, “v_line”+rand(), OBJ_VLINE, 0, TimeCurrent(), 0);”

もし何かお手伝いが必要なことがあればお知らせください。

0

FERİD ULUÇINAR

購読者、bbp_participant、3件の返信。.

プロフィールを表示

5年前 #274332

You are right, the comparison must be the opposite < instead of > used so the correct formula is (0.6 * Abs((Close(Main chart)[2] – Open(Main chart)[2]))) < Abs((Close(Main chart)[1] – Open(Main chart)[1])) meaning the current bar body (C – O) is larger than 60% of the previous bar body (C – O) To add a vertical line on each trade entry add a new action – add a Custom action and set this as a command: “ObjectCreate(0, “v_line”+rand(), OBJ_VLINE, 0, TimeCurrent(), 0);” Let me know if any help needed

Thanks for answer. Although it’s an old thread, it worked for me.

0

8件の返信を表示中 - 1 - 8件目 (全8件中)